You're using Netfos64? I'm surprised Renegade even loads with that. That's probaly the issue with the door, you more than likely need to
use NETFOSS.exe (32bit one)
Getting another error with transfering files with Zmodem, Received ZNAK instead of ZDATA frame.
No idea what that is.
Got the DOOR.SYS doors working under NetFo64 and seem to work better now than under the other BBS software using DOSBox. That is really weird. But I will take it.
Getting another error with transfering files with Zmodem, Received ZNAK instead of ZDATA frame.
No idea what that is.
Got me on that one too. Using the installed PDZmodem? Maybe install
FDSZ and see if it helps?
Double-check that DOSBox is actully in Telnet mode. The default is just raw TCP which isn't going to be fully compatible with a Telnet client. https://bleepcoder.com/dosbox-staging/688305401/telnet-support-enablement- ftmodem-serial-ports
--
Yes the PDZmodem that came with RG. Thanks for the suggestion, I will try
Double-check that DOSBox is actully in Telnet mode. The default is ju raw TCP which isn't going to be fully compatible with a Telnet client https://bleepcoder.com/dosbox-staging/688305401/telnet-support-enable ftmodem-serial-ports
--
Never occurred to me to check that. Thanks. All good info, appreciated.
Double-check that DOSBox is actully in Telnet mode. The default is just ra TCP which isn't going to be fully compatible with a Telnet client. https://bleepcoder.com/dosbox-staging/688305401/telnet-support-e ablement-for-softmodem-serial-ports
--
I don't remember the commands for DSZ anymore, but its worth a short, there was a file called "SMART PROT" out there ... maybe grab the protocol.dat from it and see if it works with the new ver or not. Of course backup your OLD ones with the pdzmodem in it or else you'll have to steal that again from a new install. ;)
On 19 Feb 2022, Rob Swindell said the following...
Double-check that DOSBox is actully in Telnet mode. The default is ju raw TCP which isn't going to be fully compatible with a Telnet client https://bleepcoder.com/dosbox-staging/688305401/telnet-support-enable ftmodem-serial-ports
--
Never occurred to me to check that. Thanks. All good info, appreciated.
Where would one find this "SMART PROT"?
Re: Re: NetFoss
By: Jeff Earle to T.J. Mcmillen on Sat Feb 19 2022 08:50 am
Got the DOOR.SYS doors working under NetFo64 and seem to work better
now than under the other BBS software using DOSBox. That is really
weird. But I will take it.
Getting another error with transfering files with Zmodem, Received
ZNAK instead of ZDATA frame.
No idea what that is.
Double-check that DOSBox is actully in Telnet mode. The default is just raw TCP which isn't going to be fully compatible with a Telnet client. https://bleepcoder.com/dosbox-staging/688305401/telnet-support-enablement-
Re: Re: NetFoss
By: Rob Swindell to Jeff Earle on Sat Feb 19 2022 12:47 pm
Re: Re: NetFoss
By: Jeff Earle to T.J. Mcmillen on Sat Feb 19 2022 08:50 am
Got the DOOR.SYS doors working under NetFo64 and seem to work better
now than under the other BBS software using DOSBox. That is really
weird. But I will take it.
Getting another error with transfering files with Zmodem, Received
ZNAK instead of ZDATA frame.
No idea what that is.
Double-check that DOSBox is actully in Telnet mode. The default is just raw TCP which isn't going to be fully compatible with a Telnet client. https://bleepcoder.com/dosbox-staging/688305401/telnet-support-enableme nt-
so right now that site is down. what specifically do i need to do in the .conf file?
Re: Re: NetFoss
By: Rob Swindell to Jeff Earle on Sat Feb 19 2022 12:47 pm
Re: Re: NetFoss
By: Jeff Earle to T.J. Mcmillen on Sat Feb 19 2022 08:50 am
Got the DOOR.SYS doors working under NetFo64 and seem to work better
now than under the other BBS software using DOSBox. That is really
weird. But I will take it.
Getting another error with transfering files with Zmodem, Received
ZNAK instead of ZDATA frame.
No idea what that is.
Double-check that DOSBox is actully in Telnet mode. The default is just raw TCP which isn't going to be fully compatible with a Telnet client. https://bleepcoder.com/dosbox-staging/688305401/telnet-support-enableme nt-
so right now that site is down.
Re: Re: NetFoss
By: Jas Hud to Rob Swindell on Mon Apr 11 2022 02:17 am
Re: Re: NetFoss
By: Rob Swindell to Jeff Earle on Sat Feb 19 2022 12:47 pm
Re: Re: NetFoss
By: Jeff Earle to T.J. Mcmillen on Sat Feb 19 2022 08:50 am
Got the DOOR.SYS doors working under NetFo64 and seem to work
better now than under the other BBS software using DOSBox. That is
really weird. But I will take it.
Getting another error with transfering files with Zmodem, Received
ZNAK instead of ZDATA frame.
No idea what that is.
Double-check that DOSBox is actully in Telnet mode. The default is
just raw TCP which isn't going to be fully compatible with a
Telnet client.
https://bleepcoder.com/dosbox-staging/688305401/telnet-support-ena
bleme nt-
so right now that site is down. what specifically do i need to do in
the .conf file?
For regular/original DOSBox, you can't do it via .conf file, but rather via "AT" command that you send to the modem. It's "ATNET1" to inform DOSBo via "AT" command that you send to the modem. It's "ATNET1" to inform DOSBo
just raw TCP which isn't going to be fully compatible with a
Telnet client.
https://bleepcoder.com/dosbox-staging/688305401/telnet-support-ena
bleme nt-
so right now that site is down.
https://github.com/dosbox-staging/dosbox-staging/issues/581
Sysop: | StingRay |
---|---|
Location: | Woodstock, GA |
Users: | 35 |
Nodes: | 15 (0 / 15) |
Uptime: | 09:25:36 |
Calls: | 616 |
Files: | 597 |
Messages: | 226,107 |